Speeds Files Revision History 1.69 Release: Description and Explanation of Changes (11.1) - Updated values for DCM (PSCLK) for -11 and -12 speed grades
1.68 Release: Description and Explanation of Changes - Updated values for FX100
- Updated values for IOBs
1.67 Release: Description and Explanation of Changes - Update to block RAM clock to out in NO_CHANGE mode
- Changed speed grades -10, -11, -12 to PRODUCTION for 4vFX40
- Changed speed grades -10, -11 to PRODUCTION for 4vFX140
- Changed speed grade -12 to PRODUCTION for 4vFX100
- Increases setup for IDELAY for speed grade -12 (4vFX100)
1.66 Release: Description and Explanation of Changes - Updated DCM component
1.65 Release: Description and Explanation of Changes - Changed FX20 and FX60 for -12 speed grade to PRODUCTION
1.64 Release: Description and Explanation of Changes- Overall slowdown of 2% for CLB delays
- Updated IDELAY min values
1.63 Release: Description and Explanation of Changes- Made SLICEM delays specific to device
1.62 Release: Description and Explanation of Changes- Increase in delays for ShiftReg(Clk 2 Out) and Flip-Flops (Setup/hold Times)
- Decrease in frequency for PPC405 components for each speed grade
- Available upon request only
1.61 Release: Description and Explanation of Changes- Change speed grade to PRODUCTION for FX12, FX20, FX60, and FX100 for -10 and -11
- Updated DCM max and min period delay parameters for FX/LX/SX
- Shift Register delays are increasing in -12 devices
1.60 Release: Description and Explanation of Changes- SX and LX devices are now PRODUCTION for -MIN speed grade (except LX300)
- Updates for DCM, IOI, EMAC, and PPC components
- Added derating support for temperature and voltage, and absolute min values
1.58 Release: Description and Explanation of Changes- This is the required minimum speeds file for all Virtex-4 LX and SX production devices
- All SX and LX devices are now PRODUCTION
.....- No change to LX25, LX60, SX35 ES and production SCD devices
.....- No timing changes
- For all other Virtex-4 devices, the following are timing changes:
- A decrease in the delay through the DCM (Tdmcko_CLK*) for STEPPING 1 devices
.....- Overall or Total Clock Path delay with a DCM will increase for OFFSET constraints
- Default DESKEW_ADJUST value changed for LX160 and FX140 from 17 to 20
- Default DESKEW_ADJUST value changed for LX200 from 17 to 21
- DS302 v1.11 reflects timing from this speeds file
1.57 Release: Description and Explanation of Changes- Added PRODUCTION timing for LX15, LX25, LX40, LX60, and SX35 devices (-10 and -11 speed grade)
- Updated data sheet for this version of the speeds file
.....- DS302 v1.10 reflects timing from this speeds file
- Updated CLB, clocking, DCM, DSP, IOB, and PPC components to create stepping-based delays
- Supports ES/SCD/Production timing based on CONFIG STEPPING setting
.....- LX/SX will have only stepping 1
.....- SCD/ES will have stepping 0
1.56 Release: Description and Explanation of Changes- Updated values for the CLB, DCM, DSP, EMAC, and IOB components
1.54 Release: Description and Explanation of Changes- Decreased negative hold values
- Decreased the frequency for FX pin of DCMs
- Updated models for GT11 and PPC
- Package flight time delays support
1.53 Release: Description and Explanation of Changes- Provided new parameters for jitter and phase-checking
- Updated I/O Standard support
- Updated parameters for clocking
1.52 Release: Description and Explanation of Changes- Updated values in the IOB components for differential I/Os
- Added an additional speed grade (-12)
- Updated clocking parameters
- Updated parameters for DCM, DSP, block RAM, and FIFO components
- Updated IDELAY default values to produce a zero hold time in legacy mode
- Updated parameters for DCI on IOB components
- Changed the -10 and -11 speed grades to ADVANCED
1.49 Release: Description and Explanation of Changes- Updated IOB and SERDES components
1.47 Release: Description and Explanation of Changes- Corrected values for the clocking component
- Updated parameters for DSP, SERDES, block RAM, FIFO, and IOB components
1.46 Release: Description and Explanation of Changes- Updated parameters for CLB, GT11, and SERDES
For information on current speeds files versions for design tool releases, see (Xilinx Answer 12201).