UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

AR# 32770

Block Memory Generator v3.2 - Release Notes and Known Issues for ISE 11.2

Description

Keywords: CORE, Generator, mem, memory, asynch, asymmetric, nonsymmetric, non-symmetric, block RAM, RAMB, block RAM, BRAM, RAMB16, RAMB, simulation, UniSim, SimPrim, unisims, simprims, NetGen, SDF

This Release Notes and Known Issues Answer Record is for the Block Memory Generator v3.2 Core, released in ISE 11.2, and contains the following information:

- General Information
- New Features
- Bug Fixes
- Known Issues

For installation instructions, general CORE Generator known issues, and design tools requirements, see the IP Release Notes Guide at:
http://www.xilinx.com/support/documentation/ip_documentation/xtp025.pdf

Solution

General Information
The Xilinx Block Memory Generator v3.2 LogiCORE should be used in all new Virtex-6, Virtex-5, Virtex-4 and Spartan-6, Spartan-3 /-3E /-3E XA /-3A /-3 XA designs wherever a block memory is required. This core supersedes the Single-Port Block Memory v6.2 and Dual-Port Block Memory v6.3 cores, but is not a direct drop-in replacement. A Block Memory Migration Kit is available on Xilinx.com to convert Single-Port Block Memory v6.2 and Dual-Port Block Memory v6.3 cores to the newer Block Memory Generator Core format.

Please see the Block Memory Core Migration Kit available at:
http://www.xilinx.com/ipcenter/blk_mem_gen/blk_mem_gen_migration_kit.htm

Also, see (Xilinx Answer 24848) for known issues of the migration kit, and (Xilinx Answer 29168) for changes made from pre-v2.4 XCO parameters.

A new CORE Generator feature is available to upgrade the Block Memory Generator from v2.4 to the latest core. This feature is part of CORE Generator, and it is visible only if you open an existing CORE Generator project with a previously generated Block Memory Generator v2.4 core. See the "Upgrading a Core" section of the CORE Generator User Guide (Software Manuals).

(Xilinx Answer 24712) How to test user logic that triggers ECC SBITERR and DBITERR outputs in the Block Memory Generator
(Xilinx Answer 31378) BitGen DRC Warnings Are Produced When DOA is Unused and DIA is Tied to Ground
(Xilinx Answer 31377) "ERROR:ip - build_algo_return: For the configured RAM size, the number of block RAMs used exceeds the maximum number of block RAMs in all available architectures (550)"


New Features in v3.2

- Support for Virtex-6 and Spartan-6 devices

Resolved Issues in v3.2

- Number of Pipeline stages within Mux unavailable for Spartan-6
- Version fixed : 3.2
- CR #510812
- In previous versions of the core, the multiplexer size reported on the CORE Generator GUI was 1 even though the multiplexer size was greater than 1, as a result of which the user was not able to select the number of Pipeline Stages within a Mux.


Known Issues in v3.2

- Virtex-6 and Spartan-6 solutions are pending hardware validation

- Software Support for the Virtex-6 Lower Power parts was added in this release, but Block Memory Generator is not yet supported and cannot be generated from CORE Generator. In order to work around this issue, you can set your project to target an equivalent Virtex-6 LXT device which will allow you to generate a place holder IP that can be regenerated when support for the Virtex-6 Lower Power parts is added in 11.3.

- Power estimation figures in the data sheet are preliminary.

(Xilinx Answer 31377) CORE Generator GUI Console displays error "For the configured RAM size, the number of block RAMs used exceeds the maximum number of 18KB block RAMs in the chosen architecture"

(Xilinx Answer 24034) Core does not generate for large memories
-The maximum size of the memory that can be generated varies depending on the machine the CORE Generator is run on. For example, a Dual Pentium-4 server running at 3.6GHz with two Gig RAM can generate a memory core that is 1.8 MBits or 230 K Bytes.
- CR 415768

(Xilinx Answer 23744) Out-of-range address input can cause the core to generate Xs on the DOUT bus

(Xilinx Answer 32815) Asynchronous reset not supported in Spartan-6
- CR 521107

Device Issues
The Virtex-4 and Virtex-5 Errata is located at:
http://www.xilinx.com/support/mysupport.htm
The Block Memory Generator Core is subject to all block RAM issues listed in the Errata.

Revision History
06/24/2009 - Initial Release
AR# 32770
Date Created 06/11/2009
Last Updated 06/18/2009
Status Active
Type General Article