UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

AR# 54130

Zynq-7000 AP SoC ZC702 Evaluation Kit - Interface Test Designs

Description

I am attempting to exercise the interfaces on the Zynq-7000 AP SoC ZC702 Evaluation Kit.

What tests can be run to ensure that the interfaces are working correctly?

Solution

Zynq-7000 AP Soc ZC702 Evaluation Kit Documentation and Example Designs referenced below can be found on the ZC702 Support page.

Feature Test Design

Notes

ZC702
Configuration Interfaces
Configuration Mode/VMode Pins ZC702 BIST (XTP180) Page 16 for QSPI; Page 41 for JTAG
Configuration PS-JTAG Interface (Xilinx Answer 46881) Also covers third-party debugger usage
Configuration PL-JTAG Interface (Xilinx Answer 46881) Also covers third-party debugger usage
Configuration PMBus Interface (Xilinx Answer 37561) Requires TI USB EVM Adapter; see (Xilinx Answer 54022)
Configuration Digilent JTAG Interface ZC702 BIST (XTP108) Page 8 uses the Digilent Interface
Configuration Xilinx Platform Cable USB Interface ZC702 BIST (XTP108) Page 8 uses the Digilent Interface; simply substitute Platform Cable USB and update SW10 settings
Configuration Quad SPI Flash ZC702 BIST (XTP108) Page 15 has user boot from QSPI.  See XTP138 for restoring QSPI factory contents
Configuration SD Card ZC702 BIST (XTP108) Page 74.  This creates a boot.bin.  Copy this to an SD Card, set SW16 for SD mode, cycle power
Board Feature Interfaces
Board XADC Interface 7 Series AMS Demonstration (UG960) Requires AMS101 card
Board FMC-LPC Connectors XM105 User Guide (UG537) Page 29.  User Guide for the XM105 Mezzanine Debug card.  This card has DS5, DS6, and DS7 which indicate good power to the board.  Debug strategies will vary depending on the specific mezzanine card being used. Can also use XTP091. Can also use the ZC702 ZVIK FMC-IMAGEON FMC card.
Board DDR3 Memory ZC702 BIST (XTP108) Page 24
Board USB ULPI Interface ZC702 BIST (XTP108) Page 28
Board Quad SPI Flash (General Purpose) none available The QSPIPS peripheral driver has examples that can perform this type of test
Board USB Serial UART ZC702 BIST (XTP108) Page 17.  Ensure that the USB UART drivers have been installed
Board SD Card (General Purpose) Xilinx Wiki Linux Release For example: 14.4 - http://wiki.xilinx.com/zynq-release-14.4.  This can boot entirely from SD card
Board HDMI Codec Interface Zynq ZC702 ZVIK (XAPP794) Ensure that HDMI monitor is 1080p capable
Board I2C Interface ZC702 BIST (XTP108) Page 19
Board 200 MHz differential clock none available Drives clock into PL fabric
Board IIC Programmable clock Zynq ZC702 ZVIK (XAPP794) Drives clock to devices on FMC-IMAGEON card
Board 33.333 MHz PSCLK ZC702 BIST (XTP108) The PS uses this clock as the primary reference clock.  If BIST works as expected, PSCLK is working
Board Ethernet PHY ZC702 BIST (XTP108) Page 38
Board CAN Interface none available The CANPS peripheral driver has examples that can perform this type of test
User Specified Interfaces
User LEDs ZC702 BIST (XTP108) Page 18
User DIP Switches ZC702 BIST (XTP108) Page 21
User Pushbuttons ZC702 BIST (XTP108) Page 21
User PMOD1 Header none available Testing requires a Digilent PMOD1 device
User PMOD2 Header none available Testing requires a Digilent PMOD2 device

Linked Answer Records

Master Answer Records

Answer Number Answer Title Version Found Version Resolved
43748 Xilinx Boards and Kits - Debug Assistant N/A N/A
50863 Zynq-7000 AP SoC - Debug N/A N/A

Associated Answer Records

Answer Number Answer Title Version Found Version Resolved
54012 Zynq-7000 AP SoC ZC702 Evaluation Kit - Board Debug Checklist N/A N/A
AR# 54130
Date Created 02/05/2013
Last Updated 06/17/2013
Status Active
Type General Article
Boards & Kits
  • Zynq-7000 All Programmable SoC ZC702 Evaluation Kit